•Februari 5, 2010 •
Tinggalkan sebuah Komentar
lakukan dengan tekan * kemudian # trus masukan passwordnya
1. Tekan *
2. Tekan #
3. Masukan password
4. Ketikan 009 [kosong kodong sembilan]
5. Tekan SPhone 1x
6. Tekan Autodial 1x
maka dilayar tampak
Jack01:ETX
tekan SPhone untuk bergulir ke Jack berikutnya, jika kita tekan sekali maka akan tampak :
Jack02:EXT101 , Ini artinya Ektension 101 ada di jack / saluran 02
jika kita ekternal 105 maka tekan tekan SPhone sampai dilayar terlihat
Jack06:ETX105 catat 06 untuk kita lanjutkan pada langkah ke -9
kemudian tekan lanjutkan lagi
6. Tekan HOLD
7. ketikan 408
8. tekan sphone 2x
9. masukan #06
CO1 = line tlp telkom 1
CO2 = line tlp telkom 2
10. Jika enable maka tlf dengan line extension itu akan berbunyi saat ada telepon dari luar yang masuk
Semoga Bermanfaat
Ditulis dalam Panasonic KX-TA308BX
•Desember 11, 2009 •
Tinggalkan sebuah Komentar
Ada dua metode yang Ok buat melihat port port yang terbuka di linux dengan menggunakan nmap yang mengscan port dan dengan menggunakan netstat. nmap dapat digunakan untuk mescan komputer kita untuk melihat port yang terbuka.
nmap -sS -O 127.0.0.1
Metode kedua dengan menggunakan netstat. netstat dapat meperlihatkan port port tersembunyi dan yang di gunakan oleh program program
netstat -nap
Ditulis dalam Linux Command Text, Umum
•Agustus 18, 2009 •
Tinggalkan sebuah Komentar
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note: you are still holding the POWER button). The printer’s carriage will “reset” or move momentarily. If the above was properly performed the printer will enter the “Service Mode”.
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM – Info printout.
3. EEPROM – Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point – However it is best leave them unaltered – You have been warned!) After selecting the desired mode (eg 4), press the POWER button to “set” the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Ditulis dalam Uncategorized
•Agustus 18, 2009 •
Tinggalkan sebuah Komentar
1: Cabut/Lepaskan Cartridge
2: Cabut/Kabel Power Listrik
3: Tutup printer (Front access panel), Tekan (jangan dilepas) tombol RESUME/RESET dan masukan Kabel Power Listrik-nya, kemudian lepas tombol yang kita tekan itu.
4: Tekan lagi RESUME/RESET sesudah kabel power terpasang.
5: Tekan RESUME/RESET selama 5 detik dan tekan lagi RESUME/RESET .
6: Tekan dan tahan RESUME/RESET selama dua detik atau lebih dan ulang ulang.
7: Tekan dan tahan RESUME/RESET selama dua detik atau lebih dan ulang ulang.
8: Unplug AC Power untuk set data.
Ditulis dalam Printer Resetter, Resetter Printer
•Agustus 11, 2009 •
Tinggalkan sebuah Komentar
Sungguh tersiksanya kalo gak bisa ngopi karena alasan yang di utarakan dokter mengenai untuk menjaga stamina kesehatan tubuhku, hmmm itulah konsekwensinya kalo kita tidak menjaga apa yang patut kita jaga yang tentunya menjaga dan memelihara kesehatan, Mungkin Allah ngasih jalan lain untuk obat pengusir ngantuk ini .. tiba tiba gw harus beranjak dari tempat duduk karena teman gw yang pakai Netbook ada masalah, dia mengajukan pertanyaan ” Fren … gimana caranya memunculkan tray icon Wirelless yang ada di bawah kanan dekat jam itu ya??”. Sambil gw hampiri seraya berkata” Hmmm pertanyaan yang super (xixixix ikutan Pak Mario Teguh)…”
Gini loh caranya, sambil gw peragakan :
Seprti kata orang bule :
“This will show you how to hide or show all System Tray icons in the Notification area of the taskbar next to the clock. By default, Vista has all System Tray icons set to show.”
Contoh: System Tray Icons Sebelum dan Sesudah


EXAMPLE: Notification Area Properties Before and After
NOTE: If the top Icons section is not grayed out, but one or more of the System icons are, then see How to Enable or Disable the Notification Area System Icons in Vista instead of this tutorial.

| METHOD ONE: |
| Through the Local Group Policy Editor |
NOTE
|
This method is only available for the Vista Business, Ultimate, and Enterprise editions. See Method TWO below for the Vista Home Basic and Home Premium editions. |
 |
1. Open the Local Group Policy Editor.
2. In the left pane, click on User Configuration, Administrative Templates, and Start Menu and Taskbar. (See screenshot below)

3. In the right pane, right click on Hide the notification area and click on Properties. (See screenshot above)
4. To Hide All System Tray Icons -
A) Select (dot) Enabled and click on OK. (See screenshot below step 5A)
B) Go to step 6.
5. To Show All System Tray Icons -
A) Select (dot) Disabled or Not Configured, then click on OK. (See screenshot below)

6. Close the Group Policy window.
7. Logoff and logon, or restart the computer to apply the changes.
| METHOD TWO: |
| Through the Registry |
NOTE
|
This method will work for all Vista editions. |
 |
Through a Download:
1. To Hide All System Tray Icons -
A) Click on the download button below to download the Hide_Tray_Icons.reg file.
B) Go to step 3.

2. To Show All System Tray Icons -
A) Click on the download button below to download the Show_Tray_Icons.reg file.

3. Click on Save, and save the .reg file to the Desktop.
4. Right click the .reg (On Desktop) file and click on Merge.
5. Click on the Run button for Security Warning pop-up.
6. Click on Continue (UAC), Yes, and then OK when prompted.
7. When done, you can delete the .reg file (On Desktop).
8. Logoff and logon, or restart the computer to apply the changes.
The Manual Way:
1. Open the Start Menu.
2. In the white line (Start Search) area, type regedit and press Enter.
3. Click on the Continue button in the UAC prompt.
4. In regedit, go to: (See screenshot below)
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer
NOTE: If Explorer is not there, then right click on Policies in the left pane and click New -> Key and type Explorer and press Enter.

5. To Hide All System Tray Icons -
A) In the right pane of the Explorer key, right click on a empty area and click New and click DWORD (32 bit) Value. (See screenshot above)
B) Type NoTrayItemsDisplay and press Enter. (See screenshot below)
C) Right click on NoTrayItemsDisplay and click on Modify.

D) Type 1 and click on OK. (See screenshot below)

E) The registry will now look like this. (See screenshot below)
F) Go to step 7.

6. To Show All System Tray Icons -
A) In the right pane, right click on NoTrayItemsDisplay and click Delete. (See screenshot above)
B) Click on Yes to confirm the deletion.
C) In regedit, go to: (See screenshot below)
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\Explorer
D) In the right pane, if NoTrayItemsDisplay is here to, then right click on it and click on Delete. (See screenshot below)
E) Click on Yes to confirm the deletion.

7. Close regedit.
8. Logoff and logon, or restart the computer to apply the changes.
That’s it,
Shawn
Ditulis dalam Vista Problem